TY - JOUR
T1 - Effects of fuel properties and aerodynamic breakup on spray under flash boiling conditions
AU - Zhao, Weihua
AU - Yan, Junhao
AU - Gao, Suya
AU - Lee, Timothy H.
AU - Li, Xiangrong
N1 - Publisher Copyright:
© 2021
PY - 2022/1/5
Y1 - 2022/1/5
N2 - The main purpose of this work is to conduct detailed comparisons of spray behavior among four important components of gasoline and to investigate the effects of fuel properties and aerodynamic breakup on spray behavior under flash boiling conditions. Isooctane, hexane, pentane, and ethanol were used as test fuels. Pressure ratio (Rp) was used as an indicator for the superheated degree and varied from 0.14 to 1.1 by adjusting the ambient pressure. Both Diffused Backlight Imaging (DBI) and Phase Doppler Anemometry (PDA) measurements were used to obtain macroscopic and microscopic characteristics of sprays. Four dimensionless numbers were used to evaluate the aerodynamic breakup processes. The results showed that as the reduction of Rp, the flash boiling intensity increased, leading to dramatic spray morphology changes and smaller droplet size, regardless of fuel type. Spray plumes merged into the spray center when lowering Rp from 1.0. Spray collapsed at an Rp of 0.28 for isooctane, hexane, and ethanol, and at an Rp of 0.18 for pentane. Fuel properties also had significant effects on spray behaviors. Spray with pentane had the smallest penetration length, and a dramatic far-field angle reduction was observed at Rp between 0.2 and 0.4, due to its higher vapor pressure and lower latent heat of vaporization. Under the same Rp, ethanol sprays had relatively larger near-field angles, far-field angles, and Sauter mean diameter (SMD), due to its high latent heat of vaporization. All the dimensionless numbers showed that the spray with pentane had the largest aerodynamic breakup intensity, followed by hexane and isooctane, while ethanol had the lowest aerodynamic breakup intensity under the tested conditions. Aerodynamic breakup still played an important role under low flash boiling intensity conditions (Rp over 0.8). Microscopic results showed that SMD of isooctane, hexane, and pentane under an Rp of 0.28 had a similar value of 10 µm.
AB - The main purpose of this work is to conduct detailed comparisons of spray behavior among four important components of gasoline and to investigate the effects of fuel properties and aerodynamic breakup on spray behavior under flash boiling conditions. Isooctane, hexane, pentane, and ethanol were used as test fuels. Pressure ratio (Rp) was used as an indicator for the superheated degree and varied from 0.14 to 1.1 by adjusting the ambient pressure. Both Diffused Backlight Imaging (DBI) and Phase Doppler Anemometry (PDA) measurements were used to obtain macroscopic and microscopic characteristics of sprays. Four dimensionless numbers were used to evaluate the aerodynamic breakup processes. The results showed that as the reduction of Rp, the flash boiling intensity increased, leading to dramatic spray morphology changes and smaller droplet size, regardless of fuel type. Spray plumes merged into the spray center when lowering Rp from 1.0. Spray collapsed at an Rp of 0.28 for isooctane, hexane, and ethanol, and at an Rp of 0.18 for pentane. Fuel properties also had significant effects on spray behaviors. Spray with pentane had the smallest penetration length, and a dramatic far-field angle reduction was observed at Rp between 0.2 and 0.4, due to its higher vapor pressure and lower latent heat of vaporization. Under the same Rp, ethanol sprays had relatively larger near-field angles, far-field angles, and Sauter mean diameter (SMD), due to its high latent heat of vaporization. All the dimensionless numbers showed that the spray with pentane had the largest aerodynamic breakup intensity, followed by hexane and isooctane, while ethanol had the lowest aerodynamic breakup intensity under the tested conditions. Aerodynamic breakup still played an important role under low flash boiling intensity conditions (Rp over 0.8). Microscopic results showed that SMD of isooctane, hexane, and pentane under an Rp of 0.28 had a similar value of 10 µm.
KW - Aerodynamic breakup
KW - Flash boiling
KW - Fuel properties
KW - Gasoline
KW - Pressure ratio
KW - Spray characteristics
UR - http://www.scopus.com/inward/record.url?scp=85116931843&partnerID=8YFLogxK
U2 - 10.1016/j.applthermaleng.2021.117646
DO - 10.1016/j.applthermaleng.2021.117646
M3 - Article
AN - SCOPUS:85116931843
SN - 1359-4311
VL - 200
JO - Applied Thermal Engineering
JF - Applied Thermal Engineering
M1 - 117646
ER -