TY - JOUR
T1 - Quasi-static compressive and cyclic dynamic impact performances of vat photopolymerization 3D printed Al2O3 triply periodic minimal surface scaffolds and Al2O3/Al hybrid structures
T2 - Effects of cell size
AU - Lu, Junjie
AU - Zhang, Xueqin
AU - Li, Suwen
AU - Zhang, Lu
AU - Wang, Wenqing
AU - Li, Zengchan
AU - Zhang, Yanpeng
AU - Wang, Gang
AU - Li, Ying
AU - He, Rujie
N1 - Publisher Copyright:
© 2023 Elsevier B.V.
PY - 2023/12/25
Y1 - 2023/12/25
N2 - In this study, Al2O3 triply periodic minimal surface (TPMS) scaffolds with cell sizes of 5 mm, 8.5 mm, and 12 mm were prepared by vat photopolymerization 3D printing, and Al2O3/Al ceramic-metal hybrid structures were subsequently obtained by the metal infiltration of AlSi10Mg. To investigate the influence of cell size on the mechanical properties of vat photopolymerization 3D printed Al2O3 TPMS scaffolds and Al2O3/Al hybrid structures, quasi-static compression and dynamic impact experiments were conducted, and the failure modes during experiments were discussed. It was shown that the quasi-static compression and dynamic impact properties of Al2O3 TPMS scaffolds gradually decreased with the increase in cell size, the compression strength decreased from 15.2 MPa to 8 MPa and the impact strength decreased from 37 MPa to 11 MPa, respectively, which was related to the stress transfer ability of the single cell. In contrast, the effects of cell size on the performance of Al2O3/Al hybrid structures were opposite. When the cell size increased, the quasi-static compression performances of the Al2O3/Al hybrid structure were greatly improved, and the compression strength increased from 175 MPa to 250 MPa. The impact resistances of the Al2O3/Al hybrid structure were further studied. The highest impact strength of the Al2O3/Al hybrid structure was 290.74 MPa. With the increase in cell size, the impact resistance of the Al2O3/Al hybrid structure had a gradual improvement trend. Under the cyclic impact, the Al2O3/Al hybrid structure showed a high impact strength and energy absorption capacity, which was mainly related to the metal phase content around the cell, i.e., the coherence of the metal phase. This study is believed to give help for the structural design of ceramic scaffolds and ceramic-metal hybrid structures.
AB - In this study, Al2O3 triply periodic minimal surface (TPMS) scaffolds with cell sizes of 5 mm, 8.5 mm, and 12 mm were prepared by vat photopolymerization 3D printing, and Al2O3/Al ceramic-metal hybrid structures were subsequently obtained by the metal infiltration of AlSi10Mg. To investigate the influence of cell size on the mechanical properties of vat photopolymerization 3D printed Al2O3 TPMS scaffolds and Al2O3/Al hybrid structures, quasi-static compression and dynamic impact experiments were conducted, and the failure modes during experiments were discussed. It was shown that the quasi-static compression and dynamic impact properties of Al2O3 TPMS scaffolds gradually decreased with the increase in cell size, the compression strength decreased from 15.2 MPa to 8 MPa and the impact strength decreased from 37 MPa to 11 MPa, respectively, which was related to the stress transfer ability of the single cell. In contrast, the effects of cell size on the performance of Al2O3/Al hybrid structures were opposite. When the cell size increased, the quasi-static compression performances of the Al2O3/Al hybrid structure were greatly improved, and the compression strength increased from 175 MPa to 250 MPa. The impact resistances of the Al2O3/Al hybrid structure were further studied. The highest impact strength of the Al2O3/Al hybrid structure was 290.74 MPa. With the increase in cell size, the impact resistance of the Al2O3/Al hybrid structure had a gradual improvement trend. Under the cyclic impact, the Al2O3/Al hybrid structure showed a high impact strength and energy absorption capacity, which was mainly related to the metal phase content around the cell, i.e., the coherence of the metal phase. This study is believed to give help for the structural design of ceramic scaffolds and ceramic-metal hybrid structures.
KW - 3D printing
KW - AlO ceramic scaffolds
KW - AlO/Al hybrid structures
KW - Cyclic shock
KW - Quasi-static compression
KW - Triply periodic minimum surface
UR - http://www.scopus.com/inward/record.url?scp=85173460866&partnerID=8YFLogxK
U2 - 10.1016/j.jallcom.2023.172445
DO - 10.1016/j.jallcom.2023.172445
M3 - Article
AN - SCOPUS:85173460866
SN - 0925-8388
VL - 969
JO - Journal of Alloys and Compounds
JF - Journal of Alloys and Compounds
M1 - 172445
ER -