TY - JOUR
T1 - Experimental characterization of needle valve dynamics and bounce control in an outwardly opening hydrogen injector
AU - Xiang, Heping
AU - Wang, Ziman
AU - Ouyang, Lingxiang
AU - Ge, Xiaocheng
AU - Liang, Tong
AU - Sun, Fengting
AU - Li, Haoxuan
N1 - Publisher Copyright:
© 2026 Elsevier Ltd.
PY - 2027/3
Y1 - 2027/3
N2 - Precise fuel injection control is critical for realizing the full efficiency and emission potential of hydrogen direct injection engines. The low viscosity and poor lubricity of hydrogen, however, bring unique challenges for injector dynamics, particularly regarding needle valve bounce and its impact on metering accuracy and durability. This paper investigates the needle‑valve dynamics of a solenoid outwardly opening hydrogen injector and evaluates a secondary‑current strategy for controlling post‑closure bounce. By using high‑speed backlit imaging, the needle‑lift profiles, response delays, velocity characteristics, and rebound behavior were measured across a wide range of injection pressures, commanded pulse widths, and back pressures. It was found that increasing injection pressure improves linearity and reduces back‑pressure sensitivity for the injected mass. Under short pulses and low pressure (≤12 bar), the needle does not reach full lift, while under high pressure (≥16 bar), full lift can be achieved easily. Opening velocity increases with increasing pressure, and closing peaks velocity (−1.3 to −1.5 m/s) generally exceeds opening peaks, indicating strong seat impact. Needle bounce is obvious, with amplitude up to 32.8 µm. A secondary‑current strategy with a dwell interval of approximately 200 µs and a second pulse duration of approximately 300 µs reduces bounce amplitude by up to 46%, with the first bounce remaining dominant. Consistent with soft-landing control principles, this suggests reduced impact velocity during seating. However, if the secondary current is applied too late (dwell ≥ 400 µs), it re‑excites the needle after seating and amplifies rebound by 170% (to 88.5 µm). These results demonstrate proper selection of injection pressure and secondary‑current timing can significantly mitigate bounce and improve metering robustness.
AB - Precise fuel injection control is critical for realizing the full efficiency and emission potential of hydrogen direct injection engines. The low viscosity and poor lubricity of hydrogen, however, bring unique challenges for injector dynamics, particularly regarding needle valve bounce and its impact on metering accuracy and durability. This paper investigates the needle‑valve dynamics of a solenoid outwardly opening hydrogen injector and evaluates a secondary‑current strategy for controlling post‑closure bounce. By using high‑speed backlit imaging, the needle‑lift profiles, response delays, velocity characteristics, and rebound behavior were measured across a wide range of injection pressures, commanded pulse widths, and back pressures. It was found that increasing injection pressure improves linearity and reduces back‑pressure sensitivity for the injected mass. Under short pulses and low pressure (≤12 bar), the needle does not reach full lift, while under high pressure (≥16 bar), full lift can be achieved easily. Opening velocity increases with increasing pressure, and closing peaks velocity (−1.3 to −1.5 m/s) generally exceeds opening peaks, indicating strong seat impact. Needle bounce is obvious, with amplitude up to 32.8 µm. A secondary‑current strategy with a dwell interval of approximately 200 µs and a second pulse duration of approximately 300 µs reduces bounce amplitude by up to 46%, with the first bounce remaining dominant. Consistent with soft-landing control principles, this suggests reduced impact velocity during seating. However, if the secondary current is applied too late (dwell ≥ 400 µs), it re‑excites the needle after seating and amplifies rebound by 170% (to 88.5 µm). These results demonstrate proper selection of injection pressure and secondary‑current timing can significantly mitigate bounce and improve metering robustness.
KW - Bounce control
KW - Hydrogen injector
KW - Needle valve dynamics
KW - Secondary current
UR - https://www.scopus.com/pages/publications/105054003809
U2 - 10.1016/j.fuel.2026.141854
DO - 10.1016/j.fuel.2026.141854
M3 - Article
AN - SCOPUS:105054003809
SN - 0016-2361
VL - 430
JO - Fuel
JF - Fuel
M1 - 141854
ER -